DIY Carbon Fiber Car Fenders Built from Scratch

Mold Consumables:

  • MDF
  • Expanding Foam
  • Body Putty
  • Duratec Sanding Primer
  • Sand Paper

Part Consumables:

  • Carbon Fiber
  • Epoxy Resin
  • Vacuum Bag
  • Release Cloth
  • Stir Sticks
  • Mixing Pails
  • Squeegee
Don’t have a CNC or the money/time for a shop to make you molds? This is a DIY guide to making accurate molds from scratch! We made these 2 molds and 4 parts in 13 days from nothing.  Check out below for a full breakdown.

Step 1: Build the Lattice

We are lucky enough to own a large scale hobby laser.  We used this to cut cross sections of the part every two inches.  The cross sections were made in the CAD program SolidWorks.  Without a hobby laser, these cross sections could be printed on paper at full scale and cut out with a jigsaw.

Custom MDF Laser Cut Lattuce for DIY Custom Fenders

Here is the full lattice with the shape taking form. This took about 8 sheets of 1/4″ MDF from Home Depot ($6.50 each). All of these are glued to another sheet of MDF and glued at all the joints.

Custom MDF Laser Cut Lattuce for DIY Custom Fenders
Once the lattice was complete, we used Great Stuff expanding foam to fill in all the slots.  Although it wasn’t ideal, it worked! I would recommend a denser expanding foam if you have time to order online.

Custom MDF Laser Cut Lattuce filled with Expanding Foam for DIY Custom Fenders

The foam will likely expand out of the top of the form and you will need to shave it down to just below the top of the wood.  I would recommend a 1/4″ gap that can be filled with Bondo in the next step.  This will provide a nice solid surface that won’t be effected by gradual changes in the foam over time.

Step 3: Create the Mold Surface

We used almost two gallons of Bondo to cover the foam and fill in the surface of the mold.  This was probably the longest part of the process and was certainly tedious.  This adds a lot of weight to the molds, but also makes them very durable.

Custom Filled Bondo Lattuce for Making Custom Fenders

Step 4: Primer the Surface

Once the mold has been covered in Bondo, multiple layers of sanding primer must be sprayed on the surface to create a nice smooth finish.  I recommend Duratec or Orca grey sanding primers.  You can use different dyes between each layer to distinguish how deep you have sanded.

Duratec Sanding Primer Sprayed Mold for Sanding

After each layer of primer, we sanded the mold and patched it with more Bondo until we created a perfect surface.  This process usually needs to be repeated 3 to 4 times to get the surface part ready.

Duratec Sanding Primer Sprayed Mold for Sanding

When spraying the final primer coat I recommend mixing it 1:1 with Duratec Hi-Gloss Additive.  This creates a layer that can be buffed to a reflective surface ready for laying up a carbon fiber part.  Here is the mold ready to go!

Final Mold for DIY Custom Carbon Fiber Fenders

Step 5: The Layup

With the mold complete, the fun part can begin! We applied 5 layers of wax to the molds letting them off gas for at least a half hour between each coat.  While we waited for this we cut the carbon, vac-bag, breather bleeder, and release cloth materials using a stencil.

Cut Carbon for Custom Carbon Fiber Fenders DIY

Using a $125 vacuum pump from Amazon we were able to pull 30 in Hg on both parts simultaneously.  The parts will need to cure for at least 8 hours, but this is largely dependent on the type of epoxy resin used.  Be sure to triple check for leaks as they will greatly affect the part’s surface finish.  Pro tip: if the pump is creating lots of smoke and noise, there is a leak in the bag that needs to be fixed.

Layup for Custom Carbon Fiber Fenders DIY

Step 6: Final Parts

Fresh out of the mold, the parts should look ready to go!  This is the sign of a good mold and layup.  Here are our first four parts prior to getting trimmed.  We ran tape lines to determine where to cut them down.  We then used a “fart saw” or reciprocating air saw as well as a Dremel to cut the parts to shape.

Final Parts with Tape Lines for Cutting

Sand down all the edges to a bullnose with 400 grit sandpaper to avoid splinters and buff and polish the outer surface until it has a mirror finish.  The pictures below are the final parts ready to go.  All steps you saw took 13 days to complete with one to two people working 5-8 hours a day.

Custom Carbon Fiber Fenders Final Photo

Final Set of DIY Carbon Fiber Fenders

Summary:

If you are interested in making custom carbon fiber fenders for your car follow these steps:

  1. Build a lattice, or Machine a Mold
  2. Fill the lattice
  3. Create the initial mold base surface
  4. Primer and finish the mold surface
  5. Do the layup (Wet or Vacuum Assisted)
  6. Trim the part
  7. Wax and buff to shine

Do you have a custom carbon fiber project you want help on?  Reach out here!


Life is Carbon Based



2 Comments

Anthony Herb · December 6, 2017 at 10:27 pm

What vacuum pump did you use? Make/model#?

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts

DIY Fabrication Guides

SEMA 2018 – BMW E30 Widebody Kit Build

SEMA 2018 – BMW E30 Widebody Kit Build  Platform: BMW E30 318is Coup (1989 – 1991) Design: Live to Offend X Khyzyl Saleem (@the_kyza) Sponsors: Toyo Tires, Live to Offend, Air Lift Performance, Studio RSR, Read more…

DIY Fabrication Guides

DIY Custom Carbon Fiber Wrapped EVO Canards

Follow along in this blog post as we wrap a pair of fiberglass canards in carbon fiber. Learn how to wrap your own parts in carbon fiber in this step-by-step picture tutorial.

DIY Fabrication Guides

DIY Custom Carbon Fiber Maserati Engine Cover

The engine cover is the centerpiece of the engine bay.  It takes up the most real estate and makes the biggest impact.  Why not convert your old plastic one to carbon fiber?